"Research use only" compounds are sold for laboratory work, so the supplies that matter are laboratory supplies: the right storage, the right tools to measure and dissolve a peptide without losing it, and the records and safety basics any lab is expected to keep. This post covers that list, drawn from the handling guides that peptide manufacturers publish for their own customers. It does not cover use in people or animals, and it explains why the FDA now treats some "supplies" on seller websites as evidence of human use.
Start with the paperwork
Before any equipment, a well-run lab has three documents for every compound:
- The certificate of analysis (COA) for the exact lot you received. Match the lot number on the vial to the lot number on the certificate, and check identity, purity and net peptide content. Our guide on how to read a peptide COA walks through it.
- The safety data sheet (SDS). Under OSHA's Hazard Communication Standard, chemical makers and distributors must provide an SDS for each hazardous chemical, and employers must keep SDSs "readily accessible" to the people who work with them.
- A written lab record. Note when each vial arrived, how it was stored, when it was opened, what solvent and volume were used, and when it was discarded. Without a record, nobody can tell later whether a strange result came from the compound or from how it was handled.
Labs covered by OSHA's laboratory standard (29 CFR 1910.1450) must also have a chemical hygiene plan: a written program of the policies, procedures and protective measures that keep workers safe, reviewed at least once a year.
Storage: cold, dry and dark
Most research peptides arrive as a freeze-dried (lyophilized) powder because they are far more stable dry than in solution. Manufacturer guidance is consistent:
- A freezer. Sigma-Aldrich advises storing lyophilized peptides at -20 °C, "or preferably at -80 °C." Bachem recommends below -15 °C, and -50 °C or colder for long-term storage. Short stays in a refrigerator at about 4 °C are acceptable.
- A desiccator. Many peptides absorb moisture from the air, and absorbed water lowers the real peptide content of what you weigh. Bachem and Sigma both advise letting a cold vial reach room temperature, ideally inside a desiccator, before opening it, so that moisture does not condense on the powder.
- Protection from light. Sigma and GenScript both recommend storing peptides away from bright light. Amber containers or a closed box in the freezer do the job.
- Tightly sealed containers. Bachem's guide says to weigh out a lyophilized peptide quickly and reseal the container tightly.
For why the dry form lasts so much longer, see why lyophilized peptides last longer.
Measuring and dissolving
A peptide in solution is a different, more fragile material, and the tools affect how much of it you actually have.
- An analytical balance for weighing powder, used quickly so the peptide picks up as little moisture as possible.
- Calibrated pipettes and sterile tips for measuring solvents accurately.
- The right solvent. Manufacturer guides start with sterile distilled water or a sterile buffer. For peptides that will not dissolve in water, they suggest a small amount of dilute acetic acid for basic peptides, or a small amount of an organic solvent such as DMSO for hydrophobic ones, then dilution. Sigma notes that peptides containing cysteine or methionine are unstable in DMSO. Both Sigma and GenScript suggest buffers around pH 5 to 6 for better storage life. Sigma also advises testing a small portion first before dissolving a whole sample.
- A 0.2 µm filter. GenScript suggests passing a peptide solution through a 0.2 µm filter to remove possible bacterial contamination.
- Low-binding tubes. Peptides stick to plastic and glass. In a manufacturer study by Eppendorf, up to 90% of a protein sample could be lost to a tube's walls within 24 hours, and some tubes sold as "low binding" recovered only a small fraction of the sample. Because that comes from a company testing its own product, treat the exact figures with caution, but the underlying problem is well known.
Keeping solutions stable
- Aliquot. Split a solution into single-use portions so each one is thawed only once. Sigma says repeated freeze-thaw cycles "should be avoided for both lyophilized peptides and peptide solutions."
- Freeze what you won't use soon. Bachem advises keeping aliquots frozen below -15 °C and says "long-term storage of peptide solutions is not recommended." Sigma's guide puts typical stability at up to a week at 4 °C.
- Know the fragile sequences. Peptides containing asparagine, glutamine, cysteine, methionine or tryptophan have shorter shelf lives, and those with cysteine, methionine or tryptophan are prone to oxidation in air. Bachem suggests oxygen-free water or buffers for them.
- Label everything with the compound, lot number, concentration, solvent and date.
Basic safety supplies
- Personal protective equipment. University safety offices set a lab coat, eye protection, long pants and closed-toe shoes as the minimum for chemical work, with gloves suited to the materials handled.
- Proper waste containers. Chemicals and broken glass do not go in the regular trash. Labs use labeled chemical-waste containers and puncture-resistant sharps containers for broken glass, collected through their environmental health and safety program.
Why some "supplies" draw FDA attention
On August 24, 2026, the FDA sent warning letters to five online peptide sellers. All of their products carried "research use only" or "not for human use" labels, and the FDA said that did not matter. In the letter to one seller, the agency wrote that "despite statements on your product labeling marketing your products 'for research use only' and 'not for human or animal consumption,' evidence obtained from your website establishes that your products are intended to be drugs for human use."
The supplies sold alongside the peptides were part of that evidence. The FDA pointed to bacteriostatic water marketed for reconstituting the sellers' peptides, together with a "peptide guide" and "peptide calculator," describing them as "resources that collectively provide the means to prepare an injectable drug for human administration." Another letter said selling the peptides and the water together showed they were intended "to be used in combination for injection." Earlier in 2026, FDA letters to sellers of research-labeled GLP-1 products made a similar point about bacteriostatic water.
The reason is simple. Bacteriostatic Water for Injection is sterile water with 0.9% benzyl alcohol as a preservative. It is a prescription drug product, and its FDA-approved labeling says it is "indicated only for diluting or dissolving drugs for intravenous, intramuscular or subcutaneous injection." The same labeling warns it is not for use in newborns, because benzyl alcohol has been linked to deaths in neonates. Laboratory work with peptides normally calls for sterile water or buffers, as the manufacturer guides above describe.
In short, the FDA judges a product by its intended use, and it reads that intent from the whole picture a seller presents, not from a disclaimer. Legal analysts at ArentFox Schiff summed up the August letters this way: "RUO labeling alone is unlikely to withstand FDA scrutiny." For more on how these labels work, see grey-market vs. compounded peptides and FDA approved vs. not approved.
A short checklist
- Certificate of analysis matched to the lot, safety data sheet and a written lab record
- Freezer at -20 °C or colder, desiccator and light-proof storage
- Analytical balance, calibrated pipettes and sterile tips
- Sterile water or buffers, plus dilute acid or DMSO only where a peptide needs them
- 0.2 µm filters and low-binding tubes for aliquots
- Labels for every vial and aliquot
- Lab coat, eye protection and gloves
- Chemical-waste and sharps containers handled through your safety program
Key references
- Bachem. Handling and storage guidelines for peptides.
- Sigma-Aldrich (Merck). Handling and storage guidelines for peptides and proteins.
- Sigma-Aldrich (Merck). Peptide solubility guidelines.
- GenScript. Peptide storage and handling.
- Grzeskowiak R, Hamels S, Gancarek J. Comparative analysis of protein recovery rates in Eppendorf LoBind and other "low binding" tubes. Eppendorf Application Note 382, 2016.
- Occupational Safety and Health Administration. Hazard Communication Standard: safety data sheets.
- Occupational Safety and Health Administration. Laboratory safety: chemical hygiene plan. Fact sheet, 2011.
- NC State Environmental Health and Safety. Personal protective equipment requirements for laboratories.
- Boston University Environmental Health and Safety. Laboratory waste disposal overview.
- U.S. Food and Drug Administration. Warning letter to Royal Peptides LLC, August 24, 2026.
- U.S. Food and Drug Administration. Warning letter to Peptide Partners LLC, August 24, 2026.
- ArentFox Schiff. RUO-ined: five peptide vendors learn that "research use only" is not a legal strategy, September 18, 2026.
- Kelley Drye. FDA turns up the heat on GLP-1 dupes sold for research use only, April 8, 2026.
- Hospira (Pfizer). Bacteriostatic Water for Injection, USP: prescribing information.
This post is educational. It describes general laboratory practice and does not give dosing guidance or instructions for use in people or animals.